← 返回博客
GB 38031battery enclosure lidlong glass fibre PA66halogen-free flame retardantthermal runawayLFT

GB 38031 Thermal Propagation: What It Means for Battery Enclosure Lid Materials

2026年5月21日

GB 38031, Electric vehicles — Traction battery safety requirements, was published in May 2020 and became mandatory in January 2021. Clause 8.2.10 — thermal diffusion — requires that from the moment a single cell goes into thermal runaway, the vehicle provide at least a five-minute escape window, with no fire or explosion of the pack as a whole. That single clause reset the material-selection logic for every structural part of the battery enclosure.

1. What a five-minute window actually demands

Thermal propagation is a chain: an adjacent cell is heated into runaway, hot gas and flame penetrate the module structure, and the whole pack follows. Delaying that chain by five minutes imposes four requirements on enclosure materials:

  • Flame retardancy — UL 94 V-0, and 5VA in stricter applications, i.e. self-extinguishing in thin wall sections
  • Thermal isolation — structural integrity for more than five minutes under direct flame at 600–900 °C
  • Halogen-free — no HCl/HBr release from decomposition, which would otherwise injure occupants through corrosive smoke
  • Melt-drip control — no molten material igniting adjacent wiring or the cabin

2. Enclosure lid options compared

MaterialWeight savingFlame retardancyProcessAssessment
Stamped steel lidbaselinenon-combustiblestamping + weldingheavy, corrodes, no part integration
Die-cast aluminium-25%non-combustibledie castinghigh cost, coolant corrosion risk
SMC (thermoset glass)-30%V-0compression mouldingnot recyclable, conflicts with ESPR
Long-glass-fibre PA66 (LFT)-35%V-0, halogen-freeinjection + compression hybridbest overall
Short-glass-fibre PA66-30%V-0 but brittlestandard injectioninsufficient impact resistance
PP + LGF-40%V-0 but temperature-limitedinjectionlow-end only, fails at cell peak temperature

Long-glass-fibre PA66 processed by LFT has become the mainstream choice at leading OEMs since 2024 for five reasons:

  1. Specific strength. Retained fibre length of 4–12 mm delivers roughly 40% more strength than short-glass compounds, allowing thinner walls.
  2. Halogen-free V-0. A phosphorus–nitrogen system reaches V-0 at 0.8 mm wall thickness.
  3. Thermal stability. HDT of 250 °C, far above PP at ~80 °C, covers cell peak temperatures.
  4. Recyclability. Thermoplastic resin can be remelted, meeting EU ESPR and recyclate-quota requirements.
  5. Part integration. Module mounts, harness channels and sealing features can be moulded in, cutting part count by 30% or more.

3. Passing the five-minute propagation test

In enclosure-lid compounds developed for leading customers, Himing has validated against the following test conditions:

  • Trigger: nail penetration plus heating
  • Flame temperature: 600–900 °C
  • Duration: ≥ 300 seconds
  • Criteria: lid remains structurally intact, no burn-through, no melt drip, halogen-free smoke

Key formulation parameters:

Formulation elementTypical value
PA66 gradehigh-viscosity PA66 (relative viscosity ≥ 2.6)
Glass-fibre content35–40% (long fibre)
Flame-retardant systemphosphate ester + melamine cyanurate (halogen-free)
Melt flow index8–15 g/10 min
UL 94 V-0 wall thickness0.8 mm
HDT @ 1.8 MPa≥ 245 °C
Notched Charpy, 23 °C≥ 12 kJ/m²

4. Compatibility with MuCell foaming

Since 2025 some leading OEMs have asked for MuCell microcellular foaming on top of LFT, for a further 10–20% weight reduction. Himing compounds are tuned for the process:

  • Matched flow (MFI adjusted to 12–18 g/10 min)
  • Flame-retardant stability under supercritical CO2/N2 injection, with no decomposition
  • No silver streaking on class-A surfaces

5. Project data

Himing long-glass-fibre PA66 is in serial supply for the battery enclosure lid of a leading OEM. Measured outcomes:

  • 35% vehicle weight reduction versus the steel design
  • 15 km additional range on a 65 kWh pack
  • GB 38031 pack-level thermal propagation test passed beyond five minutes
  • Key properties stable within ±5% batch to batch
  • Hundreds of thousands of vehicles in service with no material-related thermal incidents

Summary

GB 38031 changed the role of enclosure materials from "adequate" to "part of the thermal-propagation firewall". Long-glass-fibre PA66 with LFT processing and a halogen-free flame-retardant system is the best overall answer where weight, flame retardancy, recyclability and part integration all matter.

The Himing battery-housing-lft-pa66 series is in mass production at a leading OEM, with full GB 38031 test reports and SAE validation data available. For a spec sheet, the five-minute propagation test video or a sample request, use the inquiry form on this site.

正在做国产替代立项或需要完整 spec sheet?欢迎联系我们。

索取报价 / 技术资料