Application · Battery pack

Battery pack lid material: pass GB 38031 first, then talk about weight

The short answer: the current mainstream is long-glass-fibre PA66 (LFT) with a halogen-free V-0 system — roughly 35% lighter than a steel lid, able to integrate mounts and harness channels, and able to pass the GB 38031 pack-level five-minute propagation test. Smaller lids with lower heat load can use short-glass PA66+GF30/GF35. SMC and aluminium remain options, with recycling and cost drawbacks respectively.

Himing New Material (Zhongshan CSII) Co., Ltd. · IATF 16949 · ISO 9001 · CRCC · Zhongshan, Guangdong

1. Four hard requirements from GB 38031

Clause 8.2.10 requires at least a five-minute escape window from the moment a single cell goes into thermal runaway, with no fire or explosion of the pack. For the lid material that means four things at once.

Flame retardancy

UL94 V-0 (5VA in stricter cases), self-extinguishing in thin walls.

Thermal barrier and structure

Structurally intact for 5+ minutes under 600–900 °C direct flame, no burn-through.

Halogen-free

No HCl/HBr release that would injure occupants through corrosive smoke.

No melt drip

Molten material must not ignite nearby wiring or reach the cabin.

2. Five lid options compared

Weight saving is relative to a steel design; figures are typical industry ranges — the specific programme governs.

OptionWeightFlame ratingProcessMain drawbackFit
Stamped steelbaselinenon-combustiblestamp + weldHeavy, corrodes, no part integrationNot for new programmes
Die-cast aluminium-25%non-combustibledie castingHigh cost, coolant corrosion riskMid/high-end vehicles
SMC thermoset-30%V-0compressionNot recyclable — conflicts with ESPRLegacy programmes
Long-glass PA66 (LFT)-35%V-0, halogen-freeinjection / hybridHigh specific strength, integration, recyclableCurrent mainstream
Short-glass PA66-30%V-0standard injectionLess stiffness and impact margin than LFTSmaller lids
PP + LGF-40%V-0injectionHeat resistance too low at cell peak temperatureLow-end, non-structural

3. Why long-glass PA66 became mainstream

  • Specific strength: retained fibre length of 4–12 mm gives more strength than short glass at the same loading, so walls can be thinner.
  • Halogen-free V-0: a phosphorus–nitrogen system reaches V-0 at 0.8 mm — thin enough for large lids.
  • Heat: HDT around 245–250 °C, far above PP, covering module peak temperatures.
  • Recycling: thermoplastic, remeltable; thermoset SMC is not, and EU ESPR points the other way.
  • Integration: module mounts, harness channels and sealing features moulded in, cutting part count and assembly steps.

5. Questions engineers ask

Can a short-glass PA66 pass the five-minute GB 38031 propagation test?+
It depends on part geometry, wall thickness and FR system. Under direct flame on a large lid, a long-glass skeleton holds shape better; a short-glass design usually needs thicker walls or an extra barrier, which gives back the weight advantage. Validate on the actual lid, not on the UL94 rating of the compound alone.
Does V-0 have to be halogen-free?+
Regulation does not mandate it, but in a thermal-runaway event halogenated systems release HCl/HBr, which is a corrosive-smoke risk for occupants. Most OEMs now require halogen-free. Himing lid grades use a phosphorus–nitrogen system.
How does LFT moulding differ from standard PA66?+
LFT needs dedicated plasticising with low shear to avoid fibre breakage, and gates/runners designed around fibre orientation — otherwise weld-line strength drops sharply. We can supply the process window and filling advice.
How do you estimate the weight and range benefit?+
Use the actual lid mass difference and the vehicle mass sensitivity. For a 65 kWh pack, the published figure for a steel-to-LFT lid is roughly 35% lighter and about 15 km more range; a specific programme must be recalculated with its own parameters.

Send the lid size and propagation target

A material proposal within 24 hours; samples from 500 kg, 10-day sampling.