Application · Wire protection

Corrugated conduit: thin-wall flame rating versus flexibility

The short answer: ambient cabin runs use halogen-free FR-PP, UL94 V-2 — density 0.93, tensile 62.5 MPa, which balances flexibility and cost. Where V-0 is required in ambient zones, use a high-efficiency FR-PP system; near heat sources or with oil exposure, move to FR PA6 or PA66. The hard part is not flame retardancy itself but keeping flex life at a 0.4–0.8 mm wall — test at the real wall thickness, never at 1.6 mm.

Himing New Material (Zhongshan CSII) Co., Ltd. · IATF 16949 · ISO 9001 · CRCC · Zhongshan, Guangdong

1. Six constraints on conduit

The first two pull against each other — that is the defining trade-off.

RequirementTypical criterionWhat it drives
Thin-wall flame ratingUL94 @ 0.4–0.8 mmThe thinner the wall, the harder V-0 becomes; a 1.6 mm rating does not transfer
Flexibility / flex fatigueRepeated bending without crackingMore flame retardant means more brittleness — the central trade-off for conduit
Temperature-40 to 125 °C (higher in the bay)Near heat sources the base resin must be PA; PP will not hold
Oil / chemical resistanceEngine oil, cleaners, brake fluidPP resists oil less than PA; oily zones need separate validation
ConstructionSlit vs closed, slit ratioSlit conduit is easier to fill but protects less; decide from the assembly sequence
Abrasion & retentionSheet-metal contact, clip retentionGrommets and tie positions are where walls wear through

2. Five options compared

Typical compound values; the moulded conduit also depends on wall thickness and corrugation geometry.

OptionTensileDensityMain drawbackFit
FR-PP, UL94 V-262.5 MPa0.93Low cost, good flexibility; heat and oil are the limitsCabin temperature zones, instrument panel, appliance harnesses
FR-PP, V-0 (custom)——Thin-wall V-0 needs a high-efficiency system; toughness dropsV-0 required in ambient zones
FR PA6 + GF, V-0123 MPa1.39Stiff and heat resistant; too rigid for conduit, poor flex fatigueHigh-temperature runs needing crush resistance
FR PA66 (custom)——Higher heat; even less flexible, higher costNear heat sources, engine bay hot zones
FR-TPE / TPV——Most flexible, best flex life; flame and oil need formulation balanceFrequent bending, exposed routing

3. Three things that get missed

  1. Quoting a 1.6 mm V-0 for thin conduit. Thin walls often land at V-2; test at the wall thickness you will mould.
  2. Flame rating without flex life. Extra FR reduces toughness, and cracking starts at the corrugation root during assembly.
  3. Ignoring oil and abrasion. PP resists oil less than PA; grommets and ties are where walls wear through — assess compound and geometry together.

5. Questions buyers ask

Why is V-0 so hard on thin conduit?+
A thin wall leaves less material to absorb heat and form char, so the FR system has less time to work. A grade rated V-0 at 1.6 mm often reaches only V-2, or no rating, at 0.6 mm. Test at the actual wall thickness.
Can we have flame retardancy and flex life together?+
Yes, at a cost. The usual routes are a more efficient FR system at lower loading, or impact modification and compatibilisers to recover toughness. If both targets are hard limits, change the base resin (TPE) rather than adding more FR.
PP or PA conduit?+
Temperature and oil decide. Ambient, oil-free and flexible points to PP; near heat or with oil exposure, PA is more stable but stiffer and dearer. Temperature is the first dividing line — PP is out above roughly 125 °C.
Slit or closed conduit?+
Slit allows later addition of wires and maintenance but offers less abrasion and sealing; closed protects fully and must be filled during assembly. Choose from the line sequence, not after tooling is built.

Send the wall thickness and the flame requirement

An FR-system recommendation at your real wall thickness; samples from 500 kg in 7–10 days.